Product Overview

Terrapaste P12 is a paste type acrylic tile adhesive with non-slump characteristics. Terrapaste P12 complies with requirements as per EN12004 and passes all test requirements for D1T classified adhesives. Terrapaste P12 is suitable for interior walls for use on all types of masonry substrates such as gypsum board and sand /cement render.

Terrapaste P12 is specially formulated without the use of solvents, formaldehyde and any other harmful chemical. Terrapaste P12 is a member of the Terraco ECOLIFE product group which ensures minimal environmental impact.

Properties

• Good adhesion
• Easy workability
• Non-slump
• Environmentally friendly ecoLIFE formulation.

Areas Of Use

General purpose non-slump ceramic and mosaic tile adhesive for use on all type of interior walls such as gypsum board, cement based render, tile backer board.

Application Method

Preparation of Surface

New surfaces: Ensure that all dust, dirt and foreign matter are scraped and brushed away. Also ensure the surfaces are free from salts, oil, grease and ridges. Protect all adjacent surfaces not to be covered. All cracks, chips, voids and damages should be repaired with Terraco Handycoat Exterior.

Old surfaces: Before applying to old surfaces, ensure the substrate is firm. First wash down the surface with a sugar soap solution, rinse and allow to dry before repairing or applying the primer.

Application & Cleaning of tools

Apply Terrapaste P12 in a layer approximately 3mm thick to the surface with the smooth side of a notched trowel. Pull the trowel through the applied layer using the notched side. Push and twist the tiles into place so that full adherence is obtained. Fix tiles before the adhesive layer is surface dry. Plan work accordingly.

Do not allow a “skin” to form on the surface of applied adhesive.

Clean tools and equipment with water after use

Cleaning of tools

Remove excess adhesive from the face of the tile with a wet sponge before the adhesive dries.

Expansion joints

Expansion joints, when necessary, should be incorporated at the design stage.

Available Grades

Product Overview

Terrapaste P12 is a paste type acrylic tile adhesive with non-slump characteristics. Terrapaste P12 complies with requirements as per EN12004 and passes all test requirements for D1T classified adhesives. Terrapaste P12 is suitable for interior walls for use on all types of masonry substrates such as gypsum board and sand /cement render.

Terrapaste P12 is specially formulated without the use of solvents, formaldehyde and any other harmful chemical. Terrapaste P12 is a member of the Terraco ECOLIFE product group which ensures minimal environmental impact.

Properties

• Good adhesion
• Easy workability
• Non-slump
• Environmentally friendly ecoLIFE formulation.

Areas Of Use

General purpose non-slump ceramic and mosaic tile adhesive for use on all type of interior walls such as gypsum board, cement based render, tile backer board.

Application Method

Preparation of Surface

New surfaces: Ensure that all dust, dirt and foreign matter are scraped and brushed away. Also ensure the surfaces are free from salts, oil, grease and ridges. Protect all adjacent surfaces not to be covered. All cracks, chips, voids and damages should be repaired with Terraco Handycoat Exterior.

Old surfaces: Before applying to old surfaces, ensure the substrate is firm. First wash down the surface with a sugar soap solution, rinse and allow to dry before repairing or applying the primer.

Application & Cleaning of tools

Apply Terrapaste P12 in a layer approximately 3mm thick to the surface with the smooth side of a notched trowel. Pull the trowel through the applied layer using the notched side. Push and twist the tiles into place so that full adherence is obtained. Fix tiles before the adhesive layer is surface dry. Plan work accordingly.

Do not allow a “skin” to form on the surface of applied adhesive.

Clean tools and equipment with water after use

Cleaning of tools

Remove excess adhesive from the face of the tile with a wet sponge before the adhesive dries.

Expansion joints

Expansion joints, when necessary, should be incorporated at the design stage.

Available Grades