Product Overview

Stucco Vintage G300 is a decorative mineral skim coat finish designed to give the appearance of natural cast concrete floor or wall. It is easy to apply and has excellent strength, abrasion resistance and durability. It can be used on interiors as well as exterior surfaces.

A range of attractive patterns can be achieved depending on application tools and installation method. It is finished with an acrylic top coat (matt finish) or epoxy clear top coat (gloss finish) resulting in an attractive sheen which is easy to maintain.

Properties

Stucco Vintage G300 has the following properties:

• Faux concrete finish
• Easy to apply
• Excellent adhesion
• Excellent durability
• High abrasion resistance
• Low VOC system

Areas Of Use

Stucco Vintage G300 is used for application on commercial floors and walls such as offices, restaurants, coffee shops, mosque, villa flooring, shops, and department stores. It can be used on Internal and external areas with normal foot traffic.

Application Method

Surface Preparation:

Concrete floors / walls should be fully cured for 3-4 weeks. Ensure that all dust, dirt, and foreign matter are scraped and brushed away. All cracks, chips, voids, and damages should be repaired first. Ensure that surface is leveled.

Priming
Apply a coat of P Primer Clear or Terrabond A solution (1:5) prior to application of Stucco Vintage smooth. On extremely absorbent porous surfaces or under extreme climatic conditions, apply 2 or 3 coats of primer.

Mixing:

Add powder to resin and mix using a drill agitator for 3 minutes until lump-free. Completely mix the full kit (10 kg powder and 5 kg resin) to form a self-leveling consistency, or mix specified powder-resin ratio (approximately 36-38% resin) to achieve a trowel applied consistency. Mixed material should be used within 15 to 20 minutes of mixing.

Application:
Stucco Vintage G300 is poured onto surface and spread with a smoothing trowel or spreader to the required thickness. Various patterns can be achieved using various application tools and method. Top coating should be applied after 48-72 hours.

For trowel application, Stucco Vintage G300 is applied in 2 coats with steel trowel. Apply first coat of 1.5-2.0 mm, allow to dry for 6-8 hours, and sand the surface with 400-600 grit fine sandpaper. Apply second coat of 1-1.5 mm, allow to dry for 6-10 hours, and sand the surface with 400-600 grit fine sandpaper to get various patterns. Apply clear coat after 8-10 hours.

Stucco Vintage Clear Coat Application:

Stucco Vintage clear coat is available in two gloss levels, High Gloss (HG) and Low Gloss (LG). For High Gloss level, use Epirok TC (solvent-free epoxy clear coat) as topcoat. For Low Gloss finish, apply Diamond Seal (water based acrylic clear coat) as topcoat. Stucco Vintage clear coat is applied in 2 coats.

Clean tools and equipment with water after use

Downloads

Stucco Vintage Brochure

view now

Available Grades

Product Overview

Stucco Vintage G300 is a decorative mineral skim coat finish designed to give the appearance of natural cast concrete floor or wall. It is easy to apply and has excellent strength, abrasion resistance and durability. It can be used on interiors as well as exterior surfaces.

A range of attractive patterns can be achieved depending on application tools and installation method. It is finished with an acrylic top coat (matt finish) or epoxy clear top coat (gloss finish) resulting in an attractive sheen which is easy to maintain.

Properties

Stucco Vintage G300 has the following properties:

• Faux concrete finish
• Easy to apply
• Excellent adhesion
• Excellent durability
• High abrasion resistance
• Low VOC system

Areas Of Use

Stucco Vintage G300 is used for application on commercial floors and walls such as offices, restaurants, coffee shops, mosque, villa flooring, shops, and department stores. It can be used on Internal and external areas with normal foot traffic.

Application Method

Surface Preparation:

Concrete floors / walls should be fully cured for 3-4 weeks. Ensure that all dust, dirt, and foreign matter are scraped and brushed away. All cracks, chips, voids, and damages should be repaired first. Ensure that surface is leveled.

Priming
Apply a coat of P Primer Clear or Terrabond A solution (1:5) prior to application of Stucco Vintage smooth. On extremely absorbent porous surfaces or under extreme climatic conditions, apply 2 or 3 coats of primer.

Mixing:

Add powder to resin and mix using a drill agitator for 3 minutes until lump-free. Completely mix the full kit (10 kg powder and 5 kg resin) to form a self-leveling consistency, or mix specified powder-resin ratio (approximately 36-38% resin) to achieve a trowel applied consistency. Mixed material should be used within 15 to 20 minutes of mixing.

Application:
Stucco Vintage G300 is poured onto surface and spread with a smoothing trowel or spreader to the required thickness. Various patterns can be achieved using various application tools and method. Top coating should be applied after 48-72 hours.

For trowel application, Stucco Vintage G300 is applied in 2 coats with steel trowel. Apply first coat of 1.5-2.0 mm, allow to dry for 6-8 hours, and sand the surface with 400-600 grit fine sandpaper. Apply second coat of 1-1.5 mm, allow to dry for 6-10 hours, and sand the surface with 400-600 grit fine sandpaper to get various patterns. Apply clear coat after 8-10 hours.

Stucco Vintage Clear Coat Application:

Stucco Vintage clear coat is available in two gloss levels, High Gloss (HG) and Low Gloss (LG). For High Gloss level, use Epirok TC (solvent-free epoxy clear coat) as topcoat. For Low Gloss finish, apply Diamond Seal (water based acrylic clear coat) as topcoat. Stucco Vintage clear coat is applied in 2 coats.

Clean tools and equipment with water after use

Downloads

Stucco Vintage Brochure

view now

Available Grades